CP LOGO 09/02/09 News You Can Use
   Autumn

In This Issue
Plumbing Fun Facts
Electrical Fun Facts
Customer Testimonials
Recipe of the Month
Winterizations Begin Now
Don't Let Your Home Become Another Fire Statistic
National Breast Cancer Awareness Month
Halloween History
SAVE MONEY!
Closing Thoughts
Join Our List
Join Our Mailing List
Helpful Links
MBE logo

Rooter n Drains

Serv Plus logo

Plumbing Fun Facts


Why are manhole covers in the U.S. round instead of square? A round manhole cover cannot fall through its circular opening, whereas a square manhole cover could be turned diagonally and fall through. Circular manhole covers are also easier to place back into original position, and do not need to be rotated for alignment.

The word "plumber" is derived from the Latin word for lead - Plumbum. Lead use to be the primary material used in the creation of pipeworks used to carry water into cities and towns, before it was found to be a cumulative poison.

Who invented the modern toilet? The flush toilet we use today came from a variety of inventions throughout history. In 1596, Sir John Harington invented a design that had a flush valve to let water out of the tank and wash-down design to empty out the bowl. In the 1880s, Thomas Crapper's plumbing company built flush toilets and received a royal warrant. He popularized the siphon system for emptying the tank, and replaced the earlier floating valve system, which was prone to leaks.

Who invented the shower? While rudimentary showers can be found throughout India, Egypt and Mesopotamia, the first real shower was invented by the Greeks around 300 B.C. Ancient Greek athletes would freshen up within the Stadiums using a piped in water supply that would spray down through showerheads shaped like the faces of boars and lions.

Hot water can be one of the most dangerous things in your home. At 120°F, 49°C, it would take 10 minutes to burn skin. At 125°F, 52°C, it would take 2 minutes to burn skin. At 140°F, 60°C, it would take 6 seconds to burn skin. At 150°F, 66°C, it would take 2 seconds to burn skin.

One of the biggest myths is on the direction the water in the toilet bowl swirls. Contrary to popular belief, the direction of the swirling water doesn't depend on whether the toilet lies in the northern or southern hemisphere. Instead, the direction the water takes depends on the direction that the bowl's rim jets are pointed. The water can be made to flush in either direction in either hemisphere.

Who's the most recognizable plumber in the world? Mario, the Italian-American plumber who lives in the Mushroom Kingdom. He is one of the most famous characters in video game history.

The average person will spend three years of their life on the toilet.

The average person visits the toilet six to eight times a day.
During these six to eight visits to the toilet a day, each individual uses approximately 57 sheets of toilet paper.

You have a 1 in 10,000 chance of being injured by a toilet.

The first toilet paper was invented in 1880, but it didn't come on a roll. Instead it came as a box, like tissues.
Scott toilet paper has been around over a hundred years. The company developed its toilet paper on a roll in 1890.
72.4% of people place their toilet paper to be pulled from over the roll, rather than under.

The toilet uses more water than any other appliance in the house.

More toilets flush during half time of the Super Bowl than during any other time of year.

A third of people flush their toilet while they're still sitting on it.

Rats can survive being flushed down toilets. On top of that, they can often return to the dwelling they were in via the same route.

Televisions are more common in Afghanistan than toilets.

A study conducted found that women wad toilet paper while men fold it.

Why Hot Water is Always on the Left Side of a Faucet?
Back in the 19th century, when indoor plumbing was introduced, water was brought into the home by hand pump. At the time, there was only one option that came out of the hand pump: cold water. Since most people were - and still are - right-handed, the pump was placed on the right side of the sink. Instant hot water was introduced many years later. With the cold water pump already occupying the right side of the sink or tub, the logical place to put the hot water faucet was on the left side of the cold water faucet. There you have it!
As for who came up with it, there's always.

Why Toilet Flush Handles are Always (or Usually) on the Left?
I mentioned above that since a majority of people are right-handed, early hand pumps were on the right side of a sink or tub. Meanwhile, toilet flush handles are always on the left. What's the deal?
Early indoor toilets had pull chains connected to overhead water tanks. Again, since most people were right handed, the pull chain hung down on the right side... the right side from the perspective of someone sitting "on the throne". As flush handles evolved into the levers we know them as today, they just happened to stay on that side; the left side from the perspective of someone looking at the toilet.

Electrical Fun Facts


One lightning bolt has enough electricity to service 200 000 homes.

First Lighthouse to use electricity - Statue of Liberty (1886)

In 1800 Count Alassandro Volta made the "voltaic pile", a battery. His experiments,along with Luigi Galvani, applying electricity to frogs legs and making them jump when touched by an electric wire prompted Mary Wollstonecraft Shelley to write FRANKENSTEIN in 1818.

In 1957 a battery was discovered in Bagdad. It was made by the Parthians, who ruled Bagdad from 250 B.C.E. to 224 C.E., and was used to electroplate silver.

The Brooklyn Bridge was the first bridge to be lit using electricity.

Every year, American homes waste more than $13 billion in energy - an average of $150 per family.

More than 10,000 homes in the United States are powered entirely by solar energy.

The electric chair was invented by a dentist.
Thomas Alva Edison (1847-1931) was one of the most well known inventors of all time with 1093 patents
During the whole of his life, Edison received only three months of formal schooling, and was dismissed from school as being retarded.

The Livermore Centennial Light was manufactured in 1901 by the Shelby Electric Company. It is a hand-blown bulb with a carbon filament. It uses approximately 4 watts of electricity. The bulb has been left burning continuously in the firehouse as a night light over the fire trucks since 1901.

Electrocution is one of the top five causes of workplace deaths.

The first use of water to generate electricity was in 1882 on the Fox river, in the USA, which produced enough power to light two paper mills and a house.

10 percent of total US generating capacity is fueled by natural gas, about the same as hydropower. More than half of US capacity is coal-fired, with nuclear accounting for 20 percent.

$212 billion in electrical bills paid by US customers each year.

An electric oven uses one kilowatt-hour of electricity in about 20 minutes, but one kilowatt-hour will power a TV for 3 hours, run a 100-watt bulb for 12 hours, and keep an electric clock ticking for 3 months.

An Electric eel can produce an electric shock of up to 650 volts at one ampere.

Currents of approximately 0.2 A are potentially fatal, because they can make the heart fibrillate, or beat in an uncontrolled manner.

Early in their history, Christmas lights were so expensive that they were more commonly rented than sold.

An electrically lighted tree was a status symbol in the early 1900s.

A 100 watt modern light bulb emits about 1600 lumens, while a single flame oil lamp form the 1800s emitted about 2400 lumens.

A generator is a device that converts mechanical energy into electrical energy. The process is based on the relationship between magnetism and electricity.

The cost of electricity is going up (both in dollars and in environmental and health impacts) and it doesn't show any signs of doing otherwise.

About half of the energy in the American grid is coal generated.

Electric energy is an intermediate form of energy. It is produced in thermal power stations (where fuel oil, gas, coal, biomass, etc. are burnt), in hydroelectric power stations and nuclear power stations. Smaller quantities are produced by wind, photovoltaic solar panels, sea tides, etc.

When electricity was first introduced into the domestic environment it was primarily for lighting.

Demand for electricity grows with great rapidity as a nation modernises and its economy develops. The United States showed a 12% increase in demand during each year of the first three decades of the twentieth century.

In the late-1800s, Nikola Tesla pioneered the generation, transmission, and use of alternating current (AC) electricity, which can be transmitted over much greater distances than direct current. Tesla's inventions used electricity to bring indoor lighting to our homes and to power industrial machines.

Electricity is a general term that encompasses a variety of phenomena resulting from the presence and flow of electric charge.

Before electricity generation began over 100 years ago, houses were lit with kerosene lamps, food was cooled in iceboxes, and rooms were warmed by wood-burning or coal-burning stoves.

Demand for solar electric energy has consistently grown by 20-25% per year over the past 20 years.

A battery produces electricity using two different metals in a chemical solution. A chemical reaction between the metals and the chemicals frees more electrons in one metal than in the other.

There are several advantages and disadvantages to hydro electric energy production. One big advantage is that energy is free once the dam is built.

In 1882 water was used to electrify two paper mills and a house on the Fox River. This was the first application of hydro electric energy.

Electricity is by no means a purely human invention, and may be observed in several forms in nature, a prominent manifestation of which is lightning.

What our customers
have to say
  
Casey's Plumbing

"Very pleased with your company. I'll be recommending you to others".
  Jo Hodges, Milwaukie

"Thom was always courteous of our home and went the extra mile for us".
  Cameron & Rhonda Azari

"Excellent - Explained everything well. Even made friends with my dog".
  Ross Wine, King City

"Thom was great! Professional and good about explaining the process".
  David Bleyle, Beaverton

"Great workmanship; competent and skilled".
  Ken Moss, Gresham

"We found all of your people to be professional, friendly and considerate".
  Michael Lowe, Beaverton

"The best! I am continuing to recommend you guys".
  Carol Smith, Beaverton

"I saw my neighbor using you guys and knew they only use good companies".
  Patricia Treece, West linn

"As usual, work was performed promptly and explained in detail".
  Dan Ziglinski, Tigard

______________________________

Metro's Best Electric

"Great attention to detail, careful and care taking of our property and house. Highly recommend this company." 
Debbie - NE Portland

"I am VERY pleased with the results and with the work that Dan did. Not only do I have plenty of power to all my appliances and outlets, I have reliable smoke detectors and security lights and a working doorbell and lights in closets where I was constantly replacing battery-operated lights. Dan was punctual every morning, picked up/cleaned up every afternoon, was clear about what work he would be doing each day, worked around my need for electricity while in the house, had great ideas to help me make the house more safe and secure, installed electrical conduits to support planned renovations of the upstairs attic and the kitchen, and was willing to explain everything I wanted to understand. I got to know him well enough that I actually miss having him around!"
Lisa - SE Portland

"They were punctual, courteous and completely professional (even put on booties upon entering my house)."
Jodi - NE Portland
______________________________

Rooter n Drains

"High level of competence, service and professionalism; we were totally impressed with the crew and excellent results of their work".
 Howard Schneider, Portland

"Appreciated recommendation for preventative maintenance on the laundry drain."
Don Bardel - Portland

"Your service representative was very efficient, professional and friendly. It was a pleasure having him in our home."
John Rendon - NW Portland

"We appreciated the courtesy, promptness and efficiency of your employees."
Salomon Marmor - Clackamas

"Pleased to have the problem taken care of within 3 hours of my call."
Jean Shvland - NE Alameda

"Was so impressed with the professional and experienced service provided."
Marilyn Paesch - Gresham

"Absolutely wonderful service each and every time!"
Robert Reed - Beaverton

"Had work done on same day that I called; excellent work! Thank you."
Paul Schiverdt - Tigard

Really appreciated the quick response, the service on Sunday and thorough job. Fantastic & thanks!"
Thomas Park - SW Portland

"Absolutely the best service I've experienced. Tech was polite and knew his job; great problem solver."
Kathy Raygosa - SE Portland

______________________________
Thanks to all for the above comments!
Recipe of the Month


Wild Rice Shrimp Saute

By: Judy Robinette Ommert
"The seafood is so good here in Florida, and shrimp is at the top of our list of favorites. Shrimp and wild rice make a delicious combination, and this dish is special enough to serve to company."

Servings  4
Prep time 15 min
Cook time 35 min
 
Original Recipe Yield 4 servings
 
Ingredients
2 1/3 cups water
4 tablespoons butter or margarine, divided
1 teaspoon lemon juice
1/2 teaspoon Worcestershire sauce
1/2 teaspoon ground mustard
1/4 teaspoon pepper
1 (6 ounce) package long grain and wild rice mix
1 pound uncooked shrimp, peeled and deveined
2 tablespoons chopped green pepper
2 tablespoons chopped green onions

Directions
In a saucepan over medium heat, combine water, 1 tablespoon butter, lemon juice, Worcestershire sauce, mustard and pepper; bring to a boil. Add rice with seasoning packet; return to a boil.

Reduce heat; cover and simmer for 25-30 minutes or until rice is tender and liquid is absorbed. Meanwhile, in a skillet over medium heat, melt remaining butter. Add shrimp, green pepper and onions. Cook and stir for 7-9 minutes or until shrimp turn pink and are cooked through. Add rice; heat through.

A special thanks to Alllrecipes.com for this contribution.

TOPOctober 2010
Greetings!

It's hard to believe but Thanksgiving and Christmas are just around the corner. This month, many will be celebrating Halloween. If you're one who decorates with lighting for Halloween, be sure to use properly sized extension cords and be careful to not overload circuits.

Last month went by like a whirl wind as I scrambled to keep our technicians busy with various advertisements. There are a number of specials out there right now and if you have a project to complete in the near future, be sure to check them out.

In this month's Newsletter you'll find an excellant story detailing how to winterize your outside faucets and crawl space. Also, there is a great story about some dangerous electrical panels you'll want to check out. if you have one of these panels, don't take chances - get a FREE estimate today for a safe
replacement.

As always, I sincerely hope you find something here you can use this month.

Until next month,

Brenda Smile
Brenda Casey / Owner and Operations Manager


Remember the freeze of 2008?
Broken Pipes - Flood Damage?

PIPE -FREEZE BREAK
 
Now is the time to start thinking about faucet winterization.

Many of the water disasters that were the result of a freeze, could have been avoided with some basic winter maintenance. One of the most common mistakes homeowners make is to either put it off too long or perform the task incorrectly. 

Standard outside faucets with winterization shut off valves.
 

If you have a garage, there is a good chance that there is an outside hose bibb or hydrant,  attached to it along with a service valve located somewhere in the garage (usually somewhere in close proximity to the water heater).

ball n waste 11
TYPICAL BALL AND WASTE VALVE

The shut off valve to your garage hydrant is either a ball and waste or another form of valve with a waste cap. Note: The "waste cap" is to allow air into the system so that when you turn off the valve to your hose bibb, air can displace the water. Turning the valve off without opening the "waste cap" will result in a vacuum. As such, water cannot drain even though the water is shut off.

Below are a couple of images to illustrate taking off the "waste cap" to prepare the faucet for draining. In theory, you are only required to loosen the "waste cap" to allow air into the system. But as you can see from the below image, there is a small rubber gasket up inside the cap. 



ball n waste 22
Opening "waste" cap to ensure drain is open

ball n waste 3


And you're still not done yet. The majority of modern outside hydrants also have an Anti Siphon Valve at the tip. Exercising this is the final step to winterize your outside hydrants. 
Clearly, it's no wonder so many end up with broken pipes even though they thought they prepared properly. Again, the most common mistake made when winterizing the above outside hydrant is that some or all of the above steps are not performed.

If you have a frost proof hydrant, the only thing you need to remember to do is disconnect the garden hose connected to it . This is because a frost proof hydrant has a long stem that will actually stop the water on the heated side of the house. So when a garden hose is left attached, the faucet barrel cannot drain. If you have left the hose connected all winter and are unsure if there is damage, simply turn it on. If it froze up, the barrel is likely cracked and will leak only when the valve is turned on.

Frostproof hosebibbs

If you have one of these, none of the information above will apply. These are "frost proof" hose bibbs and do not require seperate winterization shut off valves. The one and only thing you absolutely must do to protect these faucets is to remember to remove your garden hose before the cold season.


As you can see, this faucet has a long stem designed to stop the water on the heated side of the room. After turning this valve off, the excess water left in the faucet drains on out of the 6" to 30" barrel. But if you have a garden hose connected, it cannot drain and thus will freeze and break during harsh weather. (SEE BELOW)

When this happens, the faucet will leak everytime you turn it on to use it.

So again, if you have a frost proof faucet REMEMEBER TO DISCONNECT YOUR GARDEN HOSES BEFORE THE FREEZING WEATHER SETS IN.



FOUNDATION VENTS

house with foundation vents

Another common over sight when preparing for winter weather is leaving the foundation vents unprotected. These vents must be open in the warmer weather to allow your home to breath. But during the winter, they must be blocked to prevent arctic winds from freezing your pipes. No matter how well you insulate your pipes, if the arctic winds are allowed to enter the crawl space, they will simply take longer to freeze, but freeze they will!

FOUNDATION VENTS 2                             FOUNDATION VENTS 3
APPLY VENT COVER FROM THE OUTSIDE            OR THE INSIDE


Of course, if all this is more than you want to tackle, you can always hire a professional. For your plumbing preparations, give us a call! We'll always be there for you. 

If you just need a little advice, feel free to call Bill Casey at 971-563-9418. 

IS YOUR HOME A POTENTIAL FIRE HAZARD?

Federal Pacific and Zinsco panels are dangerous!


If you have a Federal Pacific electrical panel in your home, you may indeed have a potential fire danger. 

Information below provided by inspectapedia.com. 

Note: Inspectapedia is a "Free Encyclopedia of Building & Environmental Inspection, Testing, Diagnosis, Repair, & Problem Prevention Advice. No Conflicts of Interest: no financial relationship with products or services discussed.


FPE DANGER

FPE Stab-Lok(R) Circuit Breakers Fail to Trip
High failure rate: The central safety defect in FPE Stab-Lok(R) electrical equipment is that FPE Stab-Lok(R) circuit breakers fail to trip under overload or short-circuit conditions, at a failure rate much higher than comparable equipment made by other producers. This failure to trip occurs up to 80% of the time when the breakers are called-on to trip, depending on the individual breaker type and load. The usual industry rate of failure of a circuit breaker to trip in response to an over current or short circuit is much less than 1%.

Risk of fire or injury: When an overload or short circuit occurs in an electrical device, say an electric clothes dryer, the circuit supplying electricity to the device is supposed to be interrupted, electrical power cut off, by either a fuse or a circuit breaker. This interruption of electrical power is intended to minimize the resulting fire hazard of electrical overloads or short circuits.

A circuit breaker that fails to trip, is unsafe. It fails to protect the electrical circuit, the building and building occupants where that circuit breaker is installed. This can lead to fire, property loss, and injury or worse.

FPE Stab-Lok(R) Circuit Breakers Are a Latent Safety Hazard.
A "latent safety hazard" means that the product itself does not initiate the unsafe condition. Rather, when the unsafe condition occurs (as just described above), the product, in this case an FPE Stab-Lok(R) circuit breaker, which is intended to interrupt electrical power, fails to do its job.

An impartial review of documentation regarding this issue, and discussions of the issue with forensic experts in the field, make clear that a latent hazard exists where FPE Stab-Lok circuit breakers continue in use. The hazard is worst for double-pole breakers. Published reports of actual tests that were performed indicate that under certain conditions it is possible for one leg of these circuits to attempt to trip the breaker, resulting in a jammed breaker which will afterward not trip under any load condition.

An FPE Stab-Lok Electrical Panel Should Be Replaced, not "Inspected by an Electrician" and not "Tested".

Having the FPE Stab-Lok panel evaluated by an electrician is unfortunately of absolutely no value. A visual inspection can not predict whether a circuit breaker is going to jam on the next occurrence of an overcurrent or short circuit. While a visual might pick up evidence of a previously burned circuit breaker or panel bus connection, the absence of such evidence is not any assurance whatsoever that the panel is safe.

Having the FPE Stab-Lok panel "tested" by an electrician is dangerous. For example, placing an over current load on an electrical circuit in the building could cause a fire to occur. Further, placing an over current load on a circuit "protected" by an FPE Stab-Lok circuit breaker may actually increase the chances that the circuit breaker will fail to trip in the future, even if it appears to work when tested. Aronstein's research showed a dramatic increase in the jam-up and failure rate in these circuit breakers after they had been exposed to a first "event" such as an over-current.

"But Up to Now the Electrical Panel has Never Shown a Problem!"

A statement by a building owner or occupant that no problem has been observed in a particular FPE Stab-Lok panel is absolutely no assurance that the panel is safe. It may simply be the case that the building has not experienced an over-current or short circuit on an electrical circuit. Or an over current may have occurred, tripped a breaker, but in doing so, increased the chance that next time the same breaker will fail to trip.
It would be dangerous for a building seller, for example, to warrant the future safety of an electrical panel in the building s/he is selling.

It would be dangerous for a building buyer to rely on the claim by a seller, real estate agent, or electrician that an FPE Stab-Lok electrical panel is "safe" since all independent research indicates otherwise.

If it's an FPE Stab-lok electrical panel, it should be replaced, period.

FPE Stab-Lok(R) Equipment Means Latent Fire Hazards

It's the exceptions that cause fires. An FPE circuit breaker will appear to "work just fine" in passing along current to the circuit it feeds, until there is an over current, short circuit, or similar condition. When those exceptional conditions occur, this equipment fails to protect the circuit and the building from overheating and fires, in some cases at a failure rate around 60% of the time. I estimate that the normal industry failure rate on circuit breakers is less than .01%.

Consumers should read and follow the Commission's advice regarding circuit breakers. But this advice is insufficient. The Commission's admonition to avoid overloading circuits and to turn off and have examined devices which seem to be creating a problem is a poor substitute for reliable, automatic, overcurrent protection. It is precisely because dangerous conditions can and do occur without adequate recognition and action by a consumer that circuit breakers and fuses are installed to provide overcurrent protection in the first place.
Therefore it is hardly an adequate "fix" for FPE breakers to just tell consumers to handle these cases manually.

It is possible that some breakers may perform with adequate reliability, possibly those manufactured after the companies discovered safety defects and improper practices in listing the product, and possibly those manufactured in Canada. However, in absence of an explicit statement from the manufacturer and/or the US CPSC indicating that newer stock equipment is defect free, and considering that defects occur in both breakers and the panels themselves, and finally, that testing showed failures in both in-use equipment and new off-the-shelf devices, my advice to consumers and electricians is that these panels be replaced with newer equipment, particularly those which use 240-volt double-pole breakers described in the literature. In my opinion, if a fire or other hazard occurs with this device, neither the manufacturer nor the Commission, who have suggested in the press release that data was inconclusive or inadequate to establish a hazard, will accept responsibility for losses that may ensue.

However a building inspector, home inspector, or contractor who makes any warranty of safety, by virtue of his/her position close to the consumer, is certain bear this very liability.
So Is There an FPE Stab-Lok(R) Safety Problem or Not?
Current research now confirms the safety hazards of FPE Stab-Lok(R) equipment and documents its failure rates.

Using a larger pool of FPE Stab-Lok circuit breakers than the older CPSC and Wright Malta tests found significantly higher failure rates of FPE Stab-Lok circuit breakers, including a look at critical safety failures (breaker failed to trip at 200% of rated current or jammed) which found:
  • 80% failure rate for FPE Stab-Lok GFCI circuit breakers (n=4)
  • 12% failure rate for double pole FPE Stab-Lok circuit breakers (n=120)
  • 1% failure rate for FPE Stab-Lok single pole circuit breakers (n=345)
[The significance of these numbers can be understood more clearly if you consider that the typical failure-to-trip rate for circuit breakers in residential electrical panels is a small fraction of one percent.

How Did These Unsafe FPE Stab-Lok(R) Circuit Breakers Get Into Homes?

"In a class-action lawsuit against FPE/Reliance in New Jersey, the Court found that Federal Pacific Electric Co. (FPE) committed fraud by representing that their FPE Stab-Lok(R) circuit breakers met the applicable (UL) standard test requirements when in fact they did not. The Court's finding of fraud, published in 2005, indicates that FPE cheated on the tests that were required to obtain UL listings. The company improperly applied UL labels to circuit breakers that could not and did not meet the UL requirements. FPE covered up the defective performance of the circuit breakers by a long standing practice of fraudulent testing. 

The Court's finding helps resolve the question as to how the defective breakers got into the marketplace and into homes." 

-- 2007 FPE Stab-Lok TECHNICAL REPORT, p.1, Dr. Jess Aronstein [available at this website].Companies, Attorneys, Realtors, Home Sellers, Home Buyers with Conflicting Interests.

A home owner who intends to continue living in a home, or someone buying a new home, has a great interest in assuring that the home's electrical system is properly protected and safe, as does their insurance company. However in some circumstances such as wanting to push through the sale of a home without incident, or wishing to avoid admitting potential liability, or perhaps out of lack of accurate information, some people may still assert that this well-documented safety concern does not exist.

Some insurance companies now require that their policy holders replace FPE Stab-Lok(R) equipment in the home before they will issue homeowners insurance for the property.

Not sure if your panel is safe?

Another resource to check is, ismypanelsafe.com 

FOR QUESTIONS, CALL THE BEST

 MBE logo
503-643-8843

BACK TO TOP
Mamograms Save Lives!
 


National Breast Cancer Awareness Month (NBCAM) educates women about the importance of early detection for breast cancer. Since NBCAM's inception, mammography use has doubled, and breast cancer death rates have declined. Still, many women do not utilize mammography at regular intervals.


In recognition of the fact that mammography is the best available method of detecting breast changes that may be cancer, long before physical symptoms can be seen or felt, and that breast cancer deaths could decline further if all women age 40 and older received mammograms at regular intervals, I Brenda Casey of the Casey's Plumbing, do hereby proclaim October as National Breast Cancer Awareness Month.  I urge all women and their families to get the facts about mammography.

 

National Breast Cancer Awaraeness Month

 

For more information, please click the pink ribbon below.

 

 

Pink Ribbon

 

BACK TO TOP

History of Halloween

Halloween is a holiday celebrated on the night of October 31.

Traditional activities include trick-or-treating, bonfires, costume parties, visiting "haunted houses" and carving jack-o-lanterns.

Irish and Scottish immigrants carried versions of the tradition to North America in the nineteenth century. Other western countries embraced the holiday in the late twentieth century including Ireland, the United States, Canada, Puerto Rico and the United Kingdom as well as of Australia and New Zealand.

Halloween has its origins in the ancient Celtic festival known as Samhain (pronounced "sah-win"). 



 

The festival of Samhain is a celebration of the end of the harvest season in Gaelic culture. Samhain was a time used by the ancient pagans to take stock of supplies and prepare for winter. The ancient Gaels believed that on October 31, the boundaries between the worlds of the living and the dead overlapped and the deceased would come back to life and cause havoc such as sickness or damaged crops.


The festival would frequently involve bonfires. It is believed that the fires attracted insects to the area which attracted bats to the area. These are additional attributes of the history of Halloween.

 


Masks and consumes were worn in an attempt to mimic the evil spirits or appease them.

Trick-or-treating, is an activity for children on or around Halloween in which they proceed from house to house in costumes, asking for treats such as confectionery with the question, "Trick or treat?" The "trick" part of "trick or treat" is a threat to play a trick on the homeowner or his property if no treat is given. Trick-or-treating is one of the main traditions of Halloween. It has become socially expected that if one lives in a neighborhood with children one should purchase treats in preparation for trick-or-treaters.


The history of Halloween has evolved.  The activity is popular in the United States, the United Kingdom, Ireland, Canada, and due to increased American cultural influence in recent years, imported through exposure to US television and other media, trick-or-treating has started to occur among children in many parts of Europe, and in the Saudi Aramco camps of Dhahran, Akaria compounds and Ras Tanura in Saudi Arabia.


The most significant growth - and resistance is in the United Kingdom, where the police have threatened to prosecute parents who allow their children to carry out the "trick" element. In continental Europe, where the commerce-driven importation of Halloween is seen with more skepticism, numerous destructive or illegal "tricks" and police warnings have further raised suspicion about this game and Halloween in general.


In Ohio, Iowa, and Massachusetts, the night designated for Trick-or-treating is often referred to as Beggars Night.

Part of the history of Halloween  is Halloween costumes. The practice of dressing up in costumes and begging door to door for treats on holidays goes back to the Middle Ages, and includes Christmas wassailing.


Trick-or-treating resembles the late medieval practice of "souling," when poor folk would go door to door on Hallowmas (November 1), receiving food in return for prayers for the dead on All Souls Day (November 2). It originated in Ireland and Britain, although similar practices for the souls of the dead were found as far south as Italy. Shakespeare mentions the practice in his comedy The Two Gentlemen of Verona (1593), when Speed accuses his master of "puling [whimpering, whining], like a beggar at Hallowmas."


Yet there is no evidence that souling was ever practiced in America, and trick-or-treating may have developed in America independent of any Irish or British antecedent. There is little primary Halloween history documentation of masking or costuming on Halloween - in Ireland, the UK, or America - before 1900.


The earliest known reference to ritual begging on Halloween in English speaking North America occurs in 1911, when a newspaper in Kingston, Ontario, near the border of upstate New York, reported that it was normal for the smaller children to go street guising (see below) on Halloween between 6 and 7 p.m., visiting shops and neighbors to be rewarded with nuts and candies for their rhymes and songs. Another isolated reference appears, place unknown, in 1915, with a third reference in Chicago in 1920. The thousands of Halloween postcards produced between the turn of the 20th century and the 1920s commonly show children but do not depict trick-or-treating.

Ruth Edna Kelley, in her 1919 history of the holiday, The Book of Hallowe'en, makes no mention of such a custom in the chapter "Hallowe'en in America." It does not seem to have become a widespread practice until the 1930s, with the earliest known uses in print of the term "trick or treat" appearing in 1934, and the first use in a national publication occurring in 1939. Thus, although a quarter million Scots-Irish immigrated to America between 1717 and 1770, the Irish Potato Famine brought almost a million immigrants in 1845-1849, and British and Irish immigration to America peaked in the 1880s, ritualized begging on Halloween was virtually unknown in America until generations later.


Trick-or-treating spread from the western United States eastward, stalled by sugar rationing that began in April 1942 during World War II and did not end until June 1947.


Early national attention to trick-or-treating was given in October 1947 issues of the children's magazines Jack and Jill and Children's Activities, and by Halloween episodes of the network radio programs The Baby Snooks Show in 1946 and The Jack Benny Show and The Adventures of Ozzie and Harriet in 1948.


The custom had become firmly established in popular culture by 1952, when Walt Disney portrayed it in the cartoon Trick or Treat, Ozzie and Harriet were besieged by trick-or-treaters on an episode of their television show, and UNICEF first conducted a national campaign for children to raise funds for the charity while trick-or-treating.


Trick-or-treating on the prairie. Although some popular histories of Halloween have characterized trick-or-treating as an adult invention to rechannel Halloween activities away from vandalism, nothing in the historical record supports this theory. To the contrary, adults, as reported in newspapers from the mid-1930s to the mid-1950s, typically saw it as a form of extortion, with reactions ranging from bemused indulgence to anger. Likewise, as portrayed on radio shows, children would have to explain what trick-or-treating was to puzzled adults, and not the other way around. Sometimes even the children protested: for Halloween 1948, members of the Madison Square Boys Club in New York City carried a parade banner that read "American Boys Don't Beg."


MONEY SAVING COUPONS

COUPONS NOT GOOD WITH OTHER OFFERS
OR WORK PREVIOUSLY PERFORMED

CP COUPON 01/20/2010

R&D COUPON

MBE NEWSLETTER COUPON

TOILET W/CASH

A Word From The General Manager

It's getting to be a real problem in our world today.  Innocent homeowners call contractors looking to have work performed on their home. 
A service person shows up, and the homeowner doesn't think twice about letting that person into their home.  They presume that person is honest and coming to help them with their problem.  All too often these seemingly innocent calls turn tragic.

Not long ago, I read about a Florida woman who was killed by a registered sex offender who was performing work in her home.  In another instance, a service technician in the Minneapolis area was convicted on several counts for stealing from customers' homes.  In yet another story, an unsuspecting housewife in Missouri hired a contractor only to have him call back two weeks later and make lewd remarks over the telephone. What if this guy had done more than just make telephone calls?  You don't think about this possibly happening until it's too late.

You and your family deserve to feel comfortable and safe in your own home; to live life without fear. Women home alone with small children, the elderly, or the disabled shouldn't have to be wary of their security when calling a contractor. As a person who's been in this industry for years, it sickens me that this has
become an issue... but it has.

Knowing this, we have made a commitment to you and all of our loyal customers.  You will never have to worry about a person from our company that enters your home or be concerned about their true intentions.  As a service to you, every single one of our employees  is background checked and drug tested.  No criminal or drug addict will ever wear one of our uniforms.  We have one of the most difficult hiring processes around, and only people of high moral character are given the opportunity to be employed by us.  We then take these hard working people and provide them with the best technical and communication training offered in the country.  So, you'll know that when one of our people shows up, they're upstanding citizens who are eager and able to help you with any and all of your home's needs.

Many contractors in the home services business do not bother to practice such stringent policies...  But that's what distinguishes us from the rest.  Indeed, recently when screening applicants to fill an opening we had for a  journeyman plumber, only a very small percentage passed the drug screening. And these people are now working for someone!?

When you call Casey's Plumbing, Rooter n Drains or Metro's Best Electric, you know you're dealing with professionals who care about your personal safety, the safety of your family, and the well-being and security of your home.  We feel that's the least we can do for you.

Thanks your continued patronage.

Sincerely,
 
BILL CASEY SIGNATURE