|
RegO - 2012 Products Update
|
NEW Electrically Isolated Pigtails for Underground Containers D912 Series
These pigtails are designed specifically for use on Underground LP-Gas Containers where dielectric isolation is necessary to protect the container. 
Features: - Electrically insulated POL connection.
- Heavy duty construction.
- Individually soldered connection to the copper tubing.
- Available in 2 styles: POL x POL & 1/4" NPT x POL
M.POL x M.POL 1/4"M.NPT x M.POL D912P12 12" Length D912J12 12" Length D912P20 20" Length D912J20 20" Length D912P30 30" Length D912J30 30" Length New Adjustable Flexible Vent Kit The LV960 Series Adjustable vent kit is designed to assist in meeting the point of discharge requirements for regulators in NFPA 58. It does this by diverting the LP-Gas vapor away from sources of ignition, openings into direct vent appliances or mechanical air intakes.  FEATURES
- Tubing complies with NFPA 58 5.8.3.1 (3) this flexible tubing meets the requirements of UL 1660 "Liquid-Tight Flexible Nonmetallic Conduit".
-
Reusable nonmetallic end fittings comply with NFPA 58 5.8.3.1 (3) they meet the requirements of UL 514B, "Conduit Tubing and Cable Fittings".
-
The LV 960 Series Adjustable Vent Kit can accommodate custom installations; the reusable ends can be removed and the tubing cut to the desired length and then reinstalled.
- The Adjustable Vent Kit is supplied with two reusable end fittings installed on the flexible tubing, mounting bracket
swith self-tapping screws, 90 degree vent elbow and installation instructions.
NEW 6016RM Remote Cable Closure Kit for RegO Emergency Shutoff Valves
The 6016RM Remote Cable Release Kit is designed for manual remote shutdown of RegO 6010, AA6010, 6016, AA6016, 6024, AA6024 Emergency Shutoff Valves. The cable arrangement can easily be adapted for specific installation requirements. This kit allows for remote shutoff up to 50 feet from the Emergency Shutoff Valve. The Cable/Handle Assembly has stainless steel cable protected by a flexible plastic conduit and the Sign has pre-drilled mounting holes for brackets and the tee-handle assembly and 2" high text complying with NFPA 58 -6.11.5 requirements.
NEW 2" Heavy Duty Swi ng Check with Flow Indicator - A7616
This back check valve is designed to provide required back flow protection for the unloading riser in the bulk plant's transfer area. It is designed specifically for pipeline installation and is suitable for LP-Gas and Anhydrous Ammonia service. Product flow moves the swing check to the open position, when flow stops the spring loaded swing check closes.
Features
- Easy to read large flow indicator
- Heavy duty spring loaded swing check design
- Resilient synthetic rubber seat disc for tight shutoff
- High flow rates with low pressure drop
- May be installed either horizontally or vertically
- 1/4" F-NPT plugged boss on top of body
- 711 GPM (LPG) Liquid Capacity at 10 PSIG Drop GPM
NEW 2" & 3" Globe/Angle Valves w/built in automatic back check
HA7513AP / HA7514AP & HA7517AP / HA7518AP
The application is designed for use in conjunction with our 6588LE and 6589LE low emission filler valves installed on bobtails and transports. The valves are designed to stop flow out of the container when the hand-wheel is closed. They incorporate an automatic integral back check that is designed to allow flow back into the container to prevent liquid from becoming trapped between the 6588/89LE and the closed globe/angle valve.  Features - V-ring spring loaded pressure stem seal provides for leak-proof operation. No packing to re-tighten or replace.
- Circular bridge in globe design and a dropped seat in the angle design achieve greater flow with less pressure drop.
- Swivel seat disc assembly minimizes wear which provides for good alignment and long seat life.
- ¼" F-NPT plugged holes on upstream and downstream sides of the valve.
- Heavy duty rolled ACME stem threads provide quick action and long service life.
- Seat Disc assembly incorporates an automatic back check valve, eliminating the need for a separate hydrostatic relief valve.
|
|
GEC's 2012 RegO Regulator Program
|
 Gas Equipment Company is the oldest warehouse distributor of LPG in-process, transfer and control equipment operating in the U.S. GEC got its start in 1937 when Milt LaDue, a sales representative for Bastian-Blessing (now ECII/RegO), saw a need in the emerging propane industry. Today, GEC continues to be family owned and operated with Skeeter LaDue, 3rd generation, as the current President. . Our goal today, as we start our 75th year, is to continue to provide our customers with the best products at competitive prices with the experience and knowledge to support them. Our greatest asset is our employees. Our employees from top to bottom work as a team to be the top-of-mind source for all of your equipment needs. GEC sales representatives and customer service specialists  are factory trained and experienced in all product lines to provide dependable solutions with a personalized approach. Armed with extensive product knowledge, our sales representatives travel conducting field and classroom training seminars, providing safety information, and establishing a direct link to manufacturers.
In celebration of our 75th birthday, we are offering our best regulator program ever.
|
