Columbia PureBond
W O O D   W O R K S
March 2009 Vol. 1
Columbia Newsletter
A change in the weather
Alder Kit Cab
Wood is a "hygroscopic" material.  Simply put, that means it freely gives off or takes on water as conditions around it change.  Both wood and air have some amount of water in them.  Water tends to move quite freely from the "wetter" of the two to the "drier." Water in air is expressed as humidity, but because the amount of water air can hold varies with the temperature of the air, the percentage of water in the air at a given temperature is called relative humidity. 

During extremely cold weather, air in the workplace or in a home or office is heated to a comfortable level.  This increases the amount of water the air can hold, but unless moisture is simultaneously added does not change the amount of water actually in the air, thus decreasing the relative humidity.  When relative humidity drops below 25% at a room temperature of 65 degrees F or higher, the air will seek moisture from other sources, and the most common source is, you guessed it, wood!
Warping
Warp
Warp is any deviation from a flat plane.  In a hardwood plywood panel or component, that means that one or more corners of the panel or part will not touch a flat surface.  Cupping (across the grain), bowing (parallel to the grain), and twisting (spiral to the grain) are all reported.  In fabrication, this is usually observed as the panels are being sawn to component size.  In the home or office, it is usually observed in free attached components such as doors or shelves. 

The primary cause for warp is the dimensional change that takes place when wood gives off water as would be expected during the coldest, driest parts of the year when heating inside air is more likely. This is aggravated by the fact that wood gives off surface moisture first, thus leaving a mild to severe imbalance of moisture in the panel.  Add to this the fact that one side of the panel or component is typically more protected than the other when panels are stacked with the face up or doors are mounted with one side facing the room and the other facing the inside of the cabinet.
 
Checking
Checking
Checks, also called splits or cracks, occur when dimensional change as a result of moisture movement described above creates stresses beyond the resistance capacity of the wood in question. 

Checks usually occur parallel to the grain in species like maple or birch because this is where their weakest resistance to stress exists.  Movement that takes place in the substrate directly under the face will not normally manifest itself by checking across the grain of the face, but in the case of highly ring porous woods like red oak or even ash, the checks may develop across the weaker areas of early growth (the coarse textured wood).
 
What to do

Ok, so how do we avoid warping and checking?  There are many things that can be done, but the most important are:

  • Ensure proper gluing instructions are followed
  • Avoid lengthy warehouse time at the manufacturing facility
  • Avoid lengthy delivery times
  • Store wood in climate controlled warehouses at the distribution level and fabricator site
  • Allow panels to acclimate to any new environment prior to processing
  • Where possible, stack components face to face on uniform thickness pallets or runners and weight the stacks down with a reasonable weight between processes
  • Maintain operating conditions between 30 and 60% relative humidity and 65 degrees to 75 degrees F in production and service
  • Avoid installing any finished product on site until the heating and cooling systems are up and running, and even then allow the panels or finished goods to acclimate to the new environment before installing
  • Seal all surfaces equally
  • Allow for linear expansion in the design of the finished product - avoid nailing, screwing, or gluing panels in place wherever feasible, opting for free hanging installation utilizing "Z" clip hangers or equivalent, especially on thicker panels.
  • Make sure any drywall, mortar, concrete, or plaster surfaces are completely dry and sealed before installing panels, cabinets, or fixtures
Unfortunately, given the number of variables involved, even the above outlined precautions cannot guarantee against all warping and checking.  However, having an understanding around the natural movement of water into and out of wood, coupled with these precautions will greatly minimize the potential for either!

Regards,
Ang Schramm

Alder Kit Cab
In This Issue
A change in the weather
Warping
Checking
What to do
What is Wood Works?
Wood Works Newsletter
CFP University
This is a new service of CFP University and Ang Schramm to provide the Columbia community with tips, solutions and insights. Email Ang if you have ideas for more Wood Works subject matter. Feel free to forward to colleagues and customers that might benefit from the information.
 
Join Our Mailing List

Forward this email to customers or colleagues and they can click here to be added to the next WOOD WORKS Newsletter mailing.

Forward to a Friend
Note:
This information is offered in good faith for general purposes only. It is believed to be accurate and has been compiled from sources believed to be reliable. It is offered for your consideration, investigation, and verification.  Columbia Forest Products makes no warranty of any kind, expressed or implied, concerning the accuracy or completeness of the information and data herein. Furthermore, Columbia Forest Products will not be liable for claims relating to any party's use of, or reliance on information and data contained herein, regardless or whether it is claimed that the information and data are inaccurate, incomplete, or otherwise misleading.